ciao a tutti
pare ke le ultime zetacam siano diverse (si chiamano neue/nuove) quindi nn si aggiornano kome le altre, al mom quello ke so e':
ke si riconoscono dalle altre perke hanno la parte iniziale (ke esce dal deco) in plastica non in metallo
ke se nn si aggiornano nn leggono alkuna skeda nemmeno via++cess
una volta aggiornate dovrebbero diventare allcam
io ho skaricato il fw ma nn si kapisce bene la procedura
(se gli ammin mi danno l'ok allego lo zip, cmq sta dallo sponsor)
di seguito riporto il file istruzioni in tedesco e tradotto in inglese/italiano
se qualkuno ci kapisce qualkosa in +
o ha gia' effettuato questa procedura ...
kippo
Hallo zusammen
die neuen Zetacams P/N: PRD-CAGR-0100 sind leider nicht mit Cas Interface zu programmieren
hierzu gibt es folgende abhilfe :
man muss mit fun5 erst den modul aktivieren (1. file siehe anhang)
danach original neotion software drauf auch mit fun5 der die karten unterstützt (siehe anhang 2. file)
achtet auf die hinteren P/N nummern bei zetacam modulen :
CAXX = mit cas ok
CAEW = mit cas ok
CAGR = nur mit fun5
wenn ihr keine fun5 habt gibt es die letzte möglichkeit,
dazu müsst ihr gehäuse und platine des moduls aufmachen ,
und vo vorne gesehen links, da wo der ATMEL chip sitzt sind 2 Leiterbahnen unterbrochen,
wenn man die wieder löten tut, kann man es mit cas interafce programmieren!
thx Brasilpower
Hello together
the new Zetacams P/N: PRD-CAGR-0100 are not to be programmed unfortunately with Cas interface for this there is the following remedy:
one must activate the module with fun5 only (to 1. file see appendix)
afterwards original neotion software this also with fun5 that the maps supported (see appendix 2. to file) pays attention to the rear P/N numbers with zetacam modules:
CAXX = with cas ok
CAEW = with cas ok
CAGR = only with fun5
if it no fun5 have gives it the last possibility, in addition must open housings and plate of the module for it, and vo in front seen left, where the ATMEL chip sits is 2 conductive strips interrupted, if one solders those again does, one can program it with cas interafce!
thx Brasilpower
Ciao zuzzurelloni
il nuovo Zetacams P/N: PRD-CAGR-0100 non devono essere programmati purtroppo con l'interfaccia di Cas per questo là sono il seguente rimedio:
uno deve attivare il modulo (cam) con soltanto la fun5 (1. primo file incluso)
poi il software originale di neotion questo anche con fun5 che la card supporta (2 secondo file incluso)
fare attenzione ai numeri posteriori di P/N con i moduli dello zetacam:
CAXX = con il cas approvano
CAEW = con il cas giusto
CAGR = soltanto con fun5
se non avete nessun fun5 gli danno l'ultima possibilità, in più devono aprire gli alloggiamenti e la piastra del modulo per esso ed il Vo nella parte anteriore vista a sinistra, dove il circuito integrato di ATMEL e' posto ci sono 2 piste conduttive interrotte, se uno salda quelle, uno può programmarlo con il interafce di cas!
thx Brasilpower
pare ke le ultime zetacam siano diverse (si chiamano neue/nuove) quindi nn si aggiornano kome le altre, al mom quello ke so e':
ke si riconoscono dalle altre perke hanno la parte iniziale (ke esce dal deco) in plastica non in metallo
ke se nn si aggiornano nn leggono alkuna skeda nemmeno via++cess
una volta aggiornate dovrebbero diventare allcam
io ho skaricato il fw ma nn si kapisce bene la procedura
(se gli ammin mi danno l'ok allego lo zip, cmq sta dallo sponsor)
di seguito riporto il file istruzioni in tedesco e tradotto in inglese/italiano
se qualkuno ci kapisce qualkosa in +
o ha gia' effettuato questa procedura ...
kippo
Hallo zusammen
die neuen Zetacams P/N: PRD-CAGR-0100 sind leider nicht mit Cas Interface zu programmieren
hierzu gibt es folgende abhilfe :
man muss mit fun5 erst den modul aktivieren (1. file siehe anhang)
danach original neotion software drauf auch mit fun5 der die karten unterstützt (siehe anhang 2. file)
achtet auf die hinteren P/N nummern bei zetacam modulen :
CAXX = mit cas ok
CAEW = mit cas ok
CAGR = nur mit fun5
wenn ihr keine fun5 habt gibt es die letzte möglichkeit,
dazu müsst ihr gehäuse und platine des moduls aufmachen ,
und vo vorne gesehen links, da wo der ATMEL chip sitzt sind 2 Leiterbahnen unterbrochen,
wenn man die wieder löten tut, kann man es mit cas interafce programmieren!
thx Brasilpower
Hello together
the new Zetacams P/N: PRD-CAGR-0100 are not to be programmed unfortunately with Cas interface for this there is the following remedy:
one must activate the module with fun5 only (to 1. file see appendix)
afterwards original neotion software this also with fun5 that the maps supported (see appendix 2. to file) pays attention to the rear P/N numbers with zetacam modules:
CAXX = with cas ok
CAEW = with cas ok
CAGR = only with fun5
if it no fun5 have gives it the last possibility, in addition must open housings and plate of the module for it, and vo in front seen left, where the ATMEL chip sits is 2 conductive strips interrupted, if one solders those again does, one can program it with cas interafce!
thx Brasilpower
Ciao zuzzurelloni
il nuovo Zetacams P/N: PRD-CAGR-0100 non devono essere programmati purtroppo con l'interfaccia di Cas per questo là sono il seguente rimedio:
uno deve attivare il modulo (cam) con soltanto la fun5 (1. primo file incluso)
poi il software originale di neotion questo anche con fun5 che la card supporta (2 secondo file incluso)
fare attenzione ai numeri posteriori di P/N con i moduli dello zetacam:
CAXX = con il cas approvano
CAEW = con il cas giusto
CAGR = soltanto con fun5
se non avete nessun fun5 gli danno l'ultima possibilità, in più devono aprire gli alloggiamenti e la piastra del modulo per esso ed il Vo nella parte anteriore vista a sinistra, dove il circuito integrato di ATMEL e' posto ci sono 2 piste conduttive interrotte, se uno salda quelle, uno può programmarlo con il interafce di cas!
thx Brasilpower