• COMUNICATO IMPORTANTE: ACCOUNT BLOCCATI (16/02/2024) Clicca sul link per leggere il comunicato
  • Non sono ammesse registrazioni con indirizzi email temporanei usa e getta

Diseqc vari

The tramp

Digital-Forum Senior Plus
Registrato
4 Gennaio 2006
Messaggi
429
Un saluto a tutti.
Ho un quesito da fare:

in un impianto multifeed 16 satelliti che arrivano da una sola calata unica mediante 4 diseqc 1.0 collegati agli ingressi di uno spaun 420 F diseqc 2.1 (4 in e 1 out) li devo unire ad altri 4 lnb collegati con un diseqc 1.0 e per cui provenienti da una calata di una parabaola lontana rispetto ai primi 16 lnb.
Il punto di arrivato dei due fili delle due calate descritte sopra è dietro al ricevitore satellitare.
Per unirle in un unico filo di entrata del decoder stesso potrei usare un ulteriore d Spaun diseqc 2.1 tipo il Sur 211F?
 
Credo che devi sostituire il diseqc 2.1 a 4 ingressi con uno a 8 ingressi
 
Credo che devi sostituire il diseqc 2.1 a 4 ingressi con uno a 8 ingressi

Il problema è che non posso passare un altro cavo per tornare indietro ail diseqc 2.1
per qullo chiedevo come poterli collegare e magari usare un diseqc 2.1 tipo il Sur 211F 2 in 1 out
 
Sì, è assolutamente possibile.
È solo che il SUR211 può attivare il livello UC1 solo in diseqc 1.1, e il tuo SUR420 viene dopo (visto dal ricevitore). Ciò significa che l'ordine degli ingressi sarà un po' strano:

Per il SUR211 (in modalità uncommitted), usa l'ingresso 1 per il SUR420 (+16 LNBs), e l'ingresso 2 per l'interruttore 4/1 1.0.
Imposta il SUR420 in modalità 2 (UC2+UC3, credo). Ciò significa che i suoi numeri di ingresso diseqc nel tuo ricevitore diventeranno: 1-3-5-7 (invece di 1-2-3-4).

Il ricevitore deve preferibilmente dare una ripetizione diseqc.

Scrivo questo a memoria, quindi spero di non aver fatto un errore,

BTW. Naturalmente, anche il modo 3 (UC3+UC4) sarebbe possibile; i numeri di ingresso sarebbero allora 1-5-9-13.

Tradotto da:
Yes, that is absolutely possible.
It is just that the SUR211 can only switch on UC1 level in diseqc 1.1, and your SUR420 comes after that (seen from the receiver). That means that the order of inputs will be a bit strange:

For SUR211 (in uncommitted mode), use input 1 for the SUR420 (+16 LNBs), and input 2 for the 4/1 1.0 switch.
Set the SUR420 in mode 2 (UC2+UC3, I believe). That means that its diseqc input numbers in your receiver will become: 1-3-5-7 (instead of 1-2-3-4).

The receiver must preferrably give a diseqc repeat.

I write this from memory, so I hope I didn't make a mistake,

BTW. Of course, also mode 3 (UC3+UC4) would be possible; input numbers would then be 1-5-9-13.

Ciao,
A33
 
Sì, è assolutamente possibile.
È solo che il SUR211 può attivare il livello UC1 solo in diseqc 1.1, e il tuo SUR420 viene dopo (visto dal ricevitore). Ciò significa che l'ordine degli ingressi sarà un po' strano:

Per il SUR211 (in modalità uncommitted), usa l'ingresso 1 per il SUR420 (+16 LNBs), e l'ingresso 2 per l'interruttore 4/1 1.0.
Imposta il SUR420 in modalità 2 (UC2+UC3, credo). Ciò significa che i suoi numeri di ingresso diseqc nel tuo ricevitore diventeranno: 1-3-5-7 (invece di 1-2-3-4).

Il ricevitore deve preferibilmente dare una ripetizione diseqc.

Scrivo questo a memoria, quindi spero di non aver fatto un errore,

BTW. Naturalmente, anche il modo 3 (UC3+UC4) sarebbe possibile; i numeri di ingresso sarebbero allora 1-5-9-13.

Tradotto da:
Yes, that is absolutely possible.
It is just that the SUR211 can only switch on UC1 level in diseqc 1.1, and your SUR420 comes after that (seen from the receiver). That means that the order of inputs will be a bit strange:

For SUR211 (in uncommitted mode), use input 1 for the SUR420 (+16 LNBs), and input 2 for the 4/1 1.0 switch.
Set the SUR420 in mode 2 (UC2+UC3, I believe). That means that its diseqc input numbers in your receiver will become: 1-3-5-7 (instead of 1-2-3-4).

The receiver must preferrably give a diseqc repeat.

I write this from memory, so I hope I didn't make a mistake,

BTW. Of course, also mode 3 (UC3+UC4) would be possible; input numbers would then be 1-5-9-13.

Ciao,
A33


Ti ringrazio. Appena avrò un pò di tempo libero provvederò la configurazione consigliata
 
Indietro
Alto Basso