Gionni_P
Digital-Forum New User
Saluto tutti gli amici del Forum ...
avevo un ricevitore che funzionava ,presentava problemi con telecomando, aperto verificato tensioni,regolari richiuso ...... deceduto ,non da piu segni di vita ,non o salvato configurazione originale ,come posso recuperlo
Dati ricevitore riportati su targhette
SAT+ S3.1 /01 common interface
BQC DTES05260964 cesat+112905_14p3_3p4_ITA_1_Zar
---------------------------------------------------------
Listato riportato all'accensione con RS232 collegata
Iperterminal VT100 38400 8-N-1
--------------------------------------------------------
DebugPort initialised to 115200, 8, N, 1
Front Panel Display creation : Success
Video Matrix Not Present
---------------------------------------------
| Loader Configuration Settings |
---------------------------------------------
Loader Software Version = 4.7.4z (HW MjrVer-4)
Loader is built for Tylko boards
Loader Configured for 1 x 16 Mbit flash
Target Board has 8KB EEPROM
Target Flash MCode = 0x 200020
Target Flash DCode = 0x22C422C4
Loader supports download from Air with QPSK031X-ZARLINK_TUNER_ZL10036
Loader supports Box To Box Copy
Application Reset Address = 0x7FFDFFBE
Loader allows same version to download
---------------------------------------------
No download demanded
Resource Decompressed successfully...
Preparing to start application..
BOOT ADDRESS => [ 0x7FFDFFBE ]
------- accensione ricev con tasto premuto (freccia in basso)
DFU demanded ...
------- accensione ricev con tasto premuto (freccia in alto)
loader.c 2234> UTU demanded..
-----------------------------------------------
sul televisore --- Software Upload Through UART
Connecting to Host
To Exit OTA Press @ on the Front Panel Ver 4.7.4z
ringrazio se qualcuno mi puo mandare in pm un software originale
avevo un ricevitore che funzionava ,presentava problemi con telecomando, aperto verificato tensioni,regolari richiuso ...... deceduto ,non da piu segni di vita ,non o salvato configurazione originale ,come posso recuperlo
Dati ricevitore riportati su targhette
SAT+ S3.1 /01 common interface
BQC DTES05260964 cesat+112905_14p3_3p4_ITA_1_Zar
---------------------------------------------------------
Listato riportato all'accensione con RS232 collegata
Iperterminal VT100 38400 8-N-1
--------------------------------------------------------
DebugPort initialised to 115200, 8, N, 1
Front Panel Display creation : Success
Video Matrix Not Present
---------------------------------------------
| Loader Configuration Settings |
---------------------------------------------
Loader Software Version = 4.7.4z (HW MjrVer-4)
Loader is built for Tylko boards
Loader Configured for 1 x 16 Mbit flash
Target Board has 8KB EEPROM
Target Flash MCode = 0x 200020
Target Flash DCode = 0x22C422C4
Loader supports download from Air with QPSK031X-ZARLINK_TUNER_ZL10036
Loader supports Box To Box Copy
Application Reset Address = 0x7FFDFFBE
Loader allows same version to download
---------------------------------------------
No download demanded
Resource Decompressed successfully...
Preparing to start application..
BOOT ADDRESS => [ 0x7FFDFFBE ]
------- accensione ricev con tasto premuto (freccia in basso)
DFU demanded ...
------- accensione ricev con tasto premuto (freccia in alto)
loader.c 2234> UTU demanded..
-----------------------------------------------
sul televisore --- Software Upload Through UART
Connecting to Host
To Exit OTA Press @ on the Front Panel Ver 4.7.4z
ringrazio se qualcuno mi puo mandare in pm un software originale
Ultima modifica: