Bella fregatura o bello scherzo mi hanno fatto sul file c'era scritto xcrypt151
il bello e che non entra con il cas 3 in modalità upload per aggiornare
ci vuole per forza il suo programmatore
ma e possibile che con il cas 3 non ci sia una soluzione per resettare la cam
la procedura che ho fatto e questa ho inserito la dummy nella cam e il modulo nel apposito slot carico un file il cas fa tutto da solo masi blocca quando arriva ad upload
se la infilo nel decoder si funziona normalmente
scusa ma non e possibile infilare il dummy del cas3 nella xcam infilata nel decoder e programmarla io ci ho provato ma non và
nel sito ho trovato questo
Recovery Method for the Xcam
When it is not possible to update your cam with the programmer than can you try this we call it the recovery method
1) Use a Decoder that powers the CAM also in Stand By
2) Insert the CAM into the Decoder in off (not powered)
3) Insert the serial programmer into your XCAM
4) Switch-on the decoder and go to a FTA channel
5) Verify the installed firmware (1.01 or 1.02 or 1.03T)
6) On the PC start the X-Loader Program
Now it’s where you have to fake your CAM.
All of you is aware of the fact that in Block 2 you should write the Firmware and on Block 14 the softcam.key.
In this case (and remember on in this case of anomalous CAM), you shall insert the softcam.key in block 2 instead of block 14.
7) Press Connect
8) Go to the CAM parameters
9) Activate the loader
10) The programming starts
11) At the end of programming, do not exit from the program X-Loader !!!!!
12) With the remote, verify the CAM parameter
13) You should now read “XCAM Module” like a new virgin CAM!!
14) Now you can load the new firmware in the X-Loader and program it in block 2 of your CAM
15) Press connect (without doing anything in the CAM menu) and the firmware download will start automatically.
16) At the end of download, switch off the decoder (not powered) and remove the programmer without removing the CAM from the decoder
17) Switch on the decoder on the previously selected FTA channel
18) Read CAM parameter to verify correct firmware updating
il bello e che non entra con il cas 3 in modalità upload per aggiornare
ci vuole per forza il suo programmatore
ma e possibile che con il cas 3 non ci sia una soluzione per resettare la cam
la procedura che ho fatto e questa ho inserito la dummy nella cam e il modulo nel apposito slot carico un file il cas fa tutto da solo masi blocca quando arriva ad upload
se la infilo nel decoder si funziona normalmente
scusa ma non e possibile infilare il dummy del cas3 nella xcam infilata nel decoder e programmarla io ci ho provato ma non và
nel sito ho trovato questo
Recovery Method for the Xcam
When it is not possible to update your cam with the programmer than can you try this we call it the recovery method
1) Use a Decoder that powers the CAM also in Stand By
2) Insert the CAM into the Decoder in off (not powered)
3) Insert the serial programmer into your XCAM
4) Switch-on the decoder and go to a FTA channel
5) Verify the installed firmware (1.01 or 1.02 or 1.03T)
6) On the PC start the X-Loader Program
Now it’s where you have to fake your CAM.
All of you is aware of the fact that in Block 2 you should write the Firmware and on Block 14 the softcam.key.
In this case (and remember on in this case of anomalous CAM), you shall insert the softcam.key in block 2 instead of block 14.
7) Press Connect
8) Go to the CAM parameters
9) Activate the loader
10) The programming starts
11) At the end of programming, do not exit from the program X-Loader !!!!!
12) With the remote, verify the CAM parameter
13) You should now read “XCAM Module” like a new virgin CAM!!
14) Now you can load the new firmware in the X-Loader and program it in block 2 of your CAM
15) Press connect (without doing anything in the CAM menu) and the firmware download will start automatically.
16) At the end of download, switch off the decoder (not powered) and remove the programmer without removing the CAM from the decoder
17) Switch on the decoder on the previously selected FTA channel
18) Read CAM parameter to verify correct firmware updating
Ultima modifica: